Why ice pops stick and what actually helps
If your homemade ice pops won't budge, the problem is usually simple: frozen liquid grips the mold walls. The good news is that many molds, including the ZOKU Unicorn Ice Pop Mold, are designed with release features that make unmolding easier. The key is to use those features correctly and avoid forcing the pop, which can crack it or damage the mold.
Before you try anything, check your mold's design. Some molds have built-in side tabs that let you twist and release the pop. Others rely on a brief dip in warm water. The ZOKU Unicorn Ice Pop Mold uses side tabs, so you can twist gently to break the seal. That's the first thing to try.
What the ZOKU Unicorn Ice Pop Mold provides for easier release
- Unicorn Ice Pop Mold: Built-in side tabs make it easy to twist and release your frozen creations. These tabs are your primary tool for unmolding. Twisting the tabs helps break the bond between the pop and the mold without resorting to warm water or force.

Unicorn Ice Pop Mold - Unicorn Ice Pop Mold: The spill-proof lid keeps juices contained and messes at bay. A secure lid means you can freeze the mold flat without leaks, which also prevents pops from freezing unevenly or overflowing—common causes of sticking.
- Unicorn Ice Pop Mold: These whimsical molds are thoughtfully designed to stack neatly and maximize freezer space. Stacking keeps the mold stable in the freezer, reducing the chance of tips or tilts that can cause liquid to freeze into awkward shapes that are harder to release.
A step-by-step release routine for stubborn pops
Try these steps in order, from least to most intervention. Stop as soon as the pop releases.
- 1. Twist the side tabs: Hold the mold firmly and twist the built-in side tabs gently. This flexes the mold and helps break the seal. Avoid twisting too hard—plastic can crack.
- 2. Dip the mold base in cool water: If twisting alone doesn't work, dip the bottom of the mold (not the lid) into a bowl of cool water for a few seconds. This slightly loosens the frozen pop from the walls. Do not use hot water, which can warp plastic or melt the pop unevenly.
- 3. Pull the pop straight up: Once you feel the pop loosen, pull it straight up by the stick. Avoid wiggling side to side, which can snap the stick or break the pop.
- 4. Let it rest briefly: If the pop still resists, let the mold sit at room temperature for a minute or two. The outer layer will soften just enough to release. Never use a knife or sharp tool to pry it out—you could damage the mold or injure yourself.
Prevention: how to avoid stuck pops next time
The easiest release is the one you don't have to fight for. Start by filling the mold only to the recommended line—overfilling can cause liquid to expand into the lid and create a vacuum seal. The ZOKU Unicorn Ice Pop Mold's spill-proof lid helps here, but it's not a fill-level indicator, so leave a little headspace.
Also, make sure the mold is completely clean before each use. Residue from previous batches can create sticky spots. And when freezing, place the mold on a level shelf. The stackable design of the Unicorn mold helps, but it still needs a flat surface to freeze evenly.
Finally, don't rush the freeze. Pops that freeze slowly and evenly tend to release more cleanly than those frozen quickly at very low temperatures. If your freezer runs extremely cold, consider moving the mold to a slightly warmer spot (like the door) for the last hour of freezing.
What the catalog does not tell you about unmolding
The supplied information for the ZOKU Unicorn Ice Pop Mold confirms the side tabs, spill-proof lid, and stackable design, but it does not include specific instructions for release times, water temperature, or maximum fill levels. That means you'll need to use your judgment and the steps above as general guidance, not as manufacturer instructions. If you're unsure, start with the gentlest method—twisting the tabs—and escalate only if needed.
Also note that the catalog does not specify whether the mold is dishwasher-safe or suitable for children to use unsupervised. For care and safety, refer to the packaging or ZOKU's official guidance. The tips here focus on unmolding, not on cleaning or age suitability.


